View TSOP53236_8910565.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

tsop532.., tsop534.. www.vishay.com vishay semiconductors rev. 1.1, 22-jul-16 1 document number: 82743 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ir receiver modules for remote control systems mechnical data pinning for tsop53...: 1 = out, 2 = gnd, 3 = v s features ? improved immunity against hf and rf noise ? low supply current ? photo detector and preamplifier in one package ? internal filter for pcm frequency ? supply voltage: 2.5 v to 5.5 v ? improved immunity against optical noise ? insensitive to supply voltage ripple and noise ? compatible with wave or reflow soldering (see p version of minimold option datasheets) ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 description the tsop532.. and tsop534.. series are miniaturized ir receiver modules for infrared remote control systems. a pin diode and a preamplifier are a ssembled on lead frame, the epoxy package contains an ir filter. the demodulated output signal can be directly connected to a microprocessor for decoding. the tsop534.. series devices are optimized to suppress almost all spurious pulses from wi-fi and cfl sources. they may suppress some data signals if continuously transmitted. the tsop532.. series devices are provided primarily for compatibility with old agc2 designs. new designs should prefer the tsop534.. series containing the newer agc4. these components have not been qualified according to automotive specifications. parts table agc legacy, for long bursts (agc2) for long bursts, very noisy environments (agc4) carrier frequency 30 khz tsop53230 tsop53430 33 khz tsop53233 tsop53433 36 khz TSOP53236 tsop53436 (1)(2)(3) 38 khz tsop53238 tsop53438 (4)(5) 40 khz tsop53240 tsop53440 56 khz tsop53256 tsop53456 (6)(7) package minimold pinning 1 = out, 2 = gnd, 3 = v s dimensions (mm) 5.4 w x 6.35 h x 4.9 d mounting leaded application remote control best remote control code (1) rc-5 (2) rc-6 (3) panasonic (4) nec (5) sharp (6) r-step (7) thomson rca
tsop532.., tsop534.. www.vishay.com vishay semiconductors rev. 1.1, 22-jul-16 2 document number: 82743 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 block diagram application circuit note ? stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress ratin g only and functional operation of the device at these or any other cond itions beyond those indicated in the operational sections of t his specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect the device reliability. 30 k 2 3 1 demo- pass agc input pin band dulator control circuit 16833-13 c 1 ir receiver g nd circuit c r 1 + v s g nd tran s mitter with t s alxxxx v s v o 17170-11 out r 1 and c 1 recommended to reduce s upply ripple for v s < 2.8 v absolute maximum ratings parameter test condition symbol value unit supply voltage v s -0.3 to +6 v supply current i s 5ma output voltage v o -0.3 to 5.5 v voltage at output to supply v s - v o -0.3 to (v s + 0.3) v output current i o 5ma junction temperature t j 100 c storage temperature range t stg -25 to +85 c operating temperature range t amb -25 to +85 c power consumption t amb 85 c p tot 10 mw soldering temperature t 10 s, 1 mm from case t sd 260 c electrical and optical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit supply current e v = 0, v s = 5 v i sd 0.55 0.7 0.9 ma e v = 40 klx, sunlight i sh -0.8-ma supply voltage v s 2.5 - 5.5 v transmission distance e v = 0, test signal see fig. 1, ir diode tsal6200, i f = 200 ma d-45-m output voltage low i osl = 0.5 ma, e e = 0.7 mw/m 2 , test signal see fig. 1 v osl - - 100 mv minimum irradiance pulse width tolerance: t pi - 5/f o < t po < t pi + 6/f o , test signal see fig. 1 e e min. - 0.12 0.25 mw/m 2 maximum irradiance t pi - 5/f o < t po < t pi + 6/f o , test signal see fig. 1 e e max. 50 - - w/m 2 directivity angle of half transmission distance ? 1/2 - 45- deg
tsop532.., tsop534.. www.vishay.com vishay semiconductors rev. 1.1, 22-jul-16 3 document number: 82743 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - output active low fig. 2 - pulse length and se nsitivity in dark ambient fig. 3 - output function fig. 4 - output pulse diagram fig. 5 - frequency depe ndence of responsivity fig. 6 - sensitivity in bright ambient 16110 e e t t pi * t * t pi 10/f 0 is recommended for optimal function v o v oh v ol t optical test signal (ir diode tsal6200, i f = 0.4 a, 30 pulses, f = f 0 , t = 10 ms) output signal t d 1) t po 2) 1) 7/f 0 < t d < 15/f 0 2) t pi - 5/f 0 < t po < t pi + 6/f 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0.1 10 1000 100 000 t po - output pul s e width (m s ) e e - irradiance (mw/m 2 ) output pul s e width input bur s t length = 950 nm, optical te s t s ignal, fig. 1 e e t v o v oh v ol t 600 s 600 s t = 60 ms t on t off 94 8134 optical t est signal output signal , (see fig. 4) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.1 1 10 100 1000 10 000 t on , t off - output pul s e width (m s ) e e - irradiance (mw/m 2 ) t on t off = 950 nm, optical te s t s ignal, fig. 1 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0.7 0.9 1.1 1.3 f/f 0 - relative frequency 16925 f = f 0 5 % f(3 db) = f 0 /10 e e min. /e e - relative responsivity 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0.01 0.1 1 10 100 e e min. - thre s hold irradiance (mw/m 2 ) e e - ambient dc irradiance (w/m 2 ) wavelength of ambient illumination: = 950 nm correlation with ambient light s ource s : 10 w/m 2 = 1.4 klx ( s td. ilum. a, t = 2855 k) 10 w/m 2 = 8.2 klx (daylight, t = 5900 k)
tsop532.., tsop534.. www.vishay.com vishay semiconductors rev. 1.1, 22-jul-16 4 document number: 82743 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 7 - sensitivity vs. supply voltage disturbances fig. 8 - max. envelope du ty cycle vs. burst length fig. 9 - sensitivity vs. ambient temperature fig. 10 - relative spectral sensitivity vs. wavelength fig. 11 - horizontal directivity fig. 12 - sensitivity vs. supply voltage 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1 10 100 1000 e e min. - thre s hold irradiance (mw/m 2 ) v s rm s - ac voltage on dc s upply voltage (mv) f = f 0 f = 10 khz f = 100 khz 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0 20 40 60 80 100 120 burst length (number of cycles/burst) max. envelope duty cycle f = 38 khz, e e = 2 mw/m2 tsop532.. tsop534.. 0 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 -30 -10 10 30 50 70 90 e e min. - thre s hold irradiance (mw/m 2 ) t amb - ambient temperature ( c) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 750 800 850 900 950 1000 1050 1100 1150 21425 - wavelength (nm) s ( ) rel - relative spectral sensitivity 0.4 0.2 0 0.6 0.9 0 30 10 20 40 50 60 70 80 1.0 0.8 0.7 d rel - relative tran s mi ss ion di s tance 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 2 3 4 5 6 e e min. - s en s itivity (mw/m 2 ) v s - s upply voltage (v)
tsop532.., tsop534.. www.vishay.com vishay semiconductors rev. 1.1, 22-jul-16 5 document number: 82743 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 suitable data format this series is designed to suppress spurious output pulses due to noise or disturbance signals. the devices can distinguish data signals from noise due to differences in frequency, burst length, and en velope duty cycle. the data signal should be close to the devices band-pass center frequency (e.g. 38 khz) and fulfill the conditions in the table below. when a data signal presented to the device in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the agc to insure that no spurious pulses are present at the receivers output. some examples which are suppressed are: ? dc light (e.g. from tungsten bulbs sunlight) ? continuous signals at any frequency ? strongly or weakly modulate d patterns from fluorescent lamps with electronic ballasts (see fig. 13 or fig. 14). ? 2.4 ghz and 5 ghz wi-fi fig. 13 - ir disturban ce from fluorescent lamp with low modulation fig. 14 - ir disturban ce from fluorescent lamp with high modulation note ? for data formats with short bu rsts please see the datasheet for tsop531.., tsop533.., tsop535.. 0101520 time (ms) 16920 ir signal 5 0101520 time (ms) 16921 ir signal 5 tsop532.. tsop534.. minimum burst length 10 cy cles/burst 10 cycles/burst after each burst of length a minimum gap time is required of 10 to 70 cycles 12 cycles 10 to 35 cycles 12 cycles for bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 4 x burst length 35 cycles > 10 x burst length maximum number of continuous short bursts/second 800 1300 nec code yes preferred rc5/rc6 code yes preferred thomson 56 khz code yes preferred sharp code yes preferred suppression of interference from fluorescent lamps mild disturbance patterns are suppressed (example: signal pattern of fig. 13) complex and critical disturbance patterns are suppressed (examp le: signal pattern of fig. 14 or highly dimmed lcds)
tsop532.., tsop534.. www.vishay.com vishay semiconductors rev. 1.1, 22-jul-16 6 document number: 82743 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters not indicated tolerance s 0.2 drawing no.: 6.550-5335.01-4 i ss ue: 1; 16.09.15 marking area 0.95 7.6 15.2 0.3 1 2 3 5 2.25 5.4 ( 5 .05) 6.35 (3 x) 0.3 0.1 r2.5 r2.5 (3 x) 0.6 0.1 2.54 nom. 2.54 nom. (1.1) (0.95) (3 x) 0.85 max. cav. no. technical drawing s according to din s pecification.
tsop532.., tsop534.. www.vishay.com vishay semiconductors rev. 1.1, 22-jul-16 7 document number: 82743 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 bulk packaging standard shipping for minimold is in cond uctive plastic bags. the packing quantity is determined by weight and a maximum of 0.3 % of the components per carton may be missing. ordering information note ? d = digit, please consult the list of available series to create a valid part number. examples: tsop53438 tsop53456vi1 tsop53438ss1f packaging quantity ? 300 pieces per bag (each bag is individually boxed). ? 6 bags per carton t 2 digits frequency s p d d d o = receiver s = sensor ic and package type d d 1 digit agc
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 1 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tape and reel standards for smd ir receiver modules vishay semiconductor smd ir receivers are packaged on tape and reel. the following specification is based on iec publication 286, which take s the industrial requirements for automatic insertion into account. absolute maximum ratings, me chanical dimensions, optical and electrical characteristics for taped devices are identical to the basic catalog types and can be found in the specifications for untaped devices. packaging the tapes of components are available on reels. each reel is marked with labels which contain the following information: - vishay - type - group - tape code, normally part of type name - production code - quantity missing components up to 3 consecutive components may be missing if the gap is followed by at least 6 components. a maximum of 0.5 % of the components per reel quan tity may be missing. at least 5 empty positions are present at the start and the end of the tape to enable tape insertion. tensile strength of the tape: > 15 n number of components a. panhead smd: qu antity per reel: tt, smd top view package, 1190 pcs tr, smd side view package, 1120 pcs b. heimdall: quantity per reel: tt, heimdall top view package, 2200 pcs tr, heimdall side vi ew package, 2300 pcs c. heimdall without lens : quantity per reel: wtt, top view package, 2200 pcs wtr, side view package, 2300 pcs d. belobog: quantity per reel: tt1, 1800 pcs tt2, 7000 pcs tr, not available in side view e. belobog with shield : quantity per reel: tt1, 1500 pcs tt2, 5000 pcs f. minimold df1p: quantity per reel: df1p, 1100 pcs order designation the type designation of the device is extended by tt or tt1 for top view or tr for side view. example: tsop6238tr (reel packing) tsop75238tr (reel packing) tsop75338wtt (reel packing) tsop57438tt1 (reel packing) tsop57238htt1 (reel packing)
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 2 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 reel dimensions for panhead smd and heimdall in millimeters note ? the body structure of the reel can vary 16734
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 3 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsop..tt (top view) dimensions in millimeters a. panhead smd (tsop36... tt, tssp....tt, tsop6...tt) 16584
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 4 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsop..tt (top view) dimensions in millimeters b. heimdall smd (t sop75...tt, tsop77...tt, tssp77...tt) 0.3 3.65 16 7.5 1.75 ? 1.5 ? 1.5 2 8 4 drawing-no.: 9.700-5338.01-4 i ss ue: 4; 12.06.13 technical drawing s according to din s pecification s direction of feed
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 5 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsop..tt (top view) dimensions in millimeters c. heimdall smd without lens (tsop 75...wtt, tsop77...wtt, tssp77...wtt) 2 1.75 7.5 16 8 4 3 0.3 ? 1.5 min. ? 1.5 drawing-no.: 9.700-5341.01-4 i ss ue: 3; 06.10.15 technical drawing s according to din s pecification s direction of feed
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 6 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsop..tt1, tsop..tt2 (top view) dimensions in millimeters d. belobog (tsop37...tt1, tsop37.. .tt2, tsop57...tt1 , tsop57...tt2) leader and trailer tape: part s mounted empty trailer 200 mm min. empty leader 400 mm min. direction of pulling out unreel direction ? 60 min. ? y 2 0.5 label po s ted here coming out from reel tape po s ition (12.4) 18.4 max. ? 13 0.2 ? 21 0.8 100 mm min. with cover tape x 2:1 tape and reel dimen s ion s : (2) (1.75) (5.5) 12 0.3 (8) (4) (? 1.5) (0.3) reel s ize "y" tt1 ? 180 2 = 1800 pc s . tt2 ? 330 2 = 7000 pc s . (1.2) technical drawing s according to din s pecification s not indicated tolerance s 0.1 drawing-no.: 9.700-5347.01-4 i ss ue: 1; 14.11.11
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 7 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsop..tt1, tsop..tt2 (top view) dimensions in millimeters e. belobog with shield (tsop37...htt1, tsop37...htt2, tsop57. ..htt1, tsop57...htt2) tape and reel dimen s ion s : reel s ize "y" gs 08 ? 180 2 = 1500 pc s . gs 18 ? 330 2 = 5000 pc s . unreel direction x tape po s ition coming out from reel 2 0.5 not indicated tolerance s 0.1 ? 13 0.2 ? 21 0.8 label po s ted here ? y ? 60 min. 18.4 max. (12.4) leader and trailer tape: part s mounted empty leader 400 mm min. 100 mm min. with cover tape direction of pulling out empty trailer 200 mm min. technical drawing s according to din s pecification s x 2 : 1 reel dimen s ion s and tape drawing-no.: 9.700-5380.01-4 i ss ue: 1; 28.10.13 (8) (2) (4) (? 1.5) (1.75) (0.3) (5.5) (12)
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 8 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsop..df1p (side view) dimensions in millimeters f. minimold df1p (tsop33...df1p, tsop53...df1p) drawing-no.: 9.800-5052.v3-4 i ss ue: 1; 17.12.02 form of the leave open of the wheel i s s upplier s pecific. dimen s ion s according to iec en 60 286-3 tape width: 24 technical drawing according to din s pecification s reel hub 2:1 ? 20.2 min. 1.5 min. ? 12.8 min. ? 60 min. 24.4 +3 -0 ? 330 +0 -4 drawing-no.: 9.700-5399.01-4 i ss ue: 1; 30.06.16 (6.08) (1.5 min.) (12) (1.75) (11.5) (24) (2) (4) (1.55) (0.4) (5.25) (11.75) b b a a b - b a - a
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 9 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsop..tr (side view) dimensions in millimeters a. panhead smd (tsop36...tr, tssp6...tr, tsop6...tr) 16585
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 10 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsop..tr (side view) dimensions in millimeters b. heimdall smd (tsop75. .., tsop77..., tssp7....) drawing-no.: 9.700-5337.01-4 i ss ue: 2; 06.10.15 2 1.75 7.5 16 8 4 3.6 0.3 ? 1.5 min. ? 1.5 direction of feed 1.34 ref. technical drawing s according to din s pecification s
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 11 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 taping version tsop..tr (side view) dimensions in millimeters c. heimdall smd without lens (tso p75...wtr, tsop77...wtr, tssp...wtr) 2 1.75 7.5 16 8 4 3.6 0.3 ? 1.5 ? 1.5 drawing-no.: 9.700-5342.01-4 i ss ue: 2; 12.06.13 technical drawing s according to din s pecification s direction of feed
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 12 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 leader and trailer dimensions in millimeters cover tape reel strength according to din en 60286-3 0.1 n to 1.3 n 300 mm/min. 10 mm/min. 165 to 180 peel angle label standard bar code labels for finished goods the standard bar code labels are product labels and used for identification of goods. th e finished goods are packed in final packing area. the standard packing units are labeled with standard bar code labels be fore transported as finished goods to warehouses. the labels are on each packing unit and contain vishay semicond uctor gmbh specific data. trailer leader no devices min. 200 min. 400 start end devices 96 11818 no devices vishay semiconductor gmbh standard bar code product label (finished goods) plain writing abbreviation length item-description - 18 item-number ino 8 selection-code sel 3 lot-/serial- number batch 10 data-code cod 3 (yww) plant-code ptc 2 quantity qty 8 accepted by acc - packed by pck - mixed code indica tor mixed code - origin xxxxxxx+ company logo long bar code top type length item-number n 8 plant-code n 2 sequence-number x 3 quantity n 8 total length - 21 short bar code top type length selection-code x 3 data-code n 3 batch-number x 10 filter - 1 total length - 17
smd tape and reel www.vishay.com vishay semiconductors rev. 2.2, 01-jul-16 13 document number: 80125 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dry packaging the reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. recommended meth od of storage dry box storage is recommended as soon as the aluminum bag has been opened to preve nt moisture absorption. the following conditions should be observed, if dry boxes are not available: ? storage temperature 10 c to 30 c ? storage humidity 60 % rh max. after more than 72 h under these conditions moisture content will be too high for reflow soldering. in case of moisture absorption, the devices will recover to the former condition by drying under the following condition: 192 h at 40 c + 5 c / - 0 c and < 5 % rh (dry air / nitrogen) or 96 h at 60 c + 5 c and < 5 % rh for all device containers or 24 h at 125 c + 5 c not suitable for reel or tubes. an eia jedec ? standard jstd-020 level 4 label is included on all dry bags. eia jedec standard jstd-020 level 4 label is included on all dry bags esd precaution proper storage and handling pr ocedures should be followed to prevent esd damage to the devices especially when they are removed from the antistatic shielding bag. electrostatic sensitive devices warning labels are on the packaging. vishay semiconductors standard bar code labels the vishay semiconductors st andard bar code labels are printed at final packing areas. the labels are on each packing unit and contain vishay semiconductors specific data. outer packaging the sealed reel is packed into a pizza box. aluminum bag label reel 15973 caution this bag contains moisture-sensitive devices 1. shelf life in sealed bag: 12 months at < 40 c and < 90 % relative humidity (rh) 2. after this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 c) must be 2a. mounted within 72 hours at factory condition of < 30 c/60 % rh or 2b. stored at < 5 % rh 3. devices require baking befor mounting if: humidity indicator card is > 10 % when read at 23 c 5 c or 2a. or 2b. are not met. 4. if baking is required, devices may be baked for: 192 hours at 40 c + 5 c/- 0 c and < 5 % rh (dry air/nitrogen) or 96 hours at 60 c 5 c and < 5 % rh for all device containers or 24 hours at 125 c 5 c not suitable for reels or tubes bag seal date: (if blank, see barcode label) note: level and body temperature defined by eia jedec standard j-std-020 4 level 22522 16962 carton box dimensions in millimeters thickness width length pizza box (smd and heimdall) (taping in reels) 50 340 340 thickne ss width 22127 length
legal disclaimer notice www.vishay.com vishay revision: 13-jun-16 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: vishay: ? tsop53433? tsop53233? tsop53430? tsop53238? tsop53436? tsop53456? TSOP53236? tsop53440? tsop53240? tsop53438? tsop53230? tsop53256

▲Up To Search▲

Price & Availability of TSOP53236

	To Download TSOP53236 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .